Impulse IR
Impulse response loader with start/end trim and low/high cut
Parameters
| Parameter | Range | Default |
|---|---|---|
| IR File | File | None selected |
| Reverse | Off, On | Off |
| Start | 0 – 10000 | 0 |
| End | 0 – 30000 | 30000 |
| Low Cut | 20 – 1000 | 20 |
| High Cut | 1000 – 20000 | 20000 |
| Master | -24 – 12 | 0 |
| Normalize | Off, Energy, Response peak | Response peak |
Mix is the standard device mix (not listed above).
Overview
Impulse IR convolves the input with an impulse response audio file. An IR can capture a speaker cabinet, microphone chain, room, plate, or other linear system, so the sound depends mostly on the selected IR File. Impulse IR reads WAV, FLAC, and AIFF files, mono or stereo. A stereo file keeps its separate left and right responses. Files at a different sample rate than the system are resampled when they load. The convolution adds no latency.
Choosing an IR
Tap LOAD IR (or the IR name at the top of the screen) to browse the IR folder. The LOAD IR light is on while an IR is loaded. PREV IR and NEXT IR step through the other IRs in the same folder in name order, and wrap around at either end.
The top of the screen shows the loaded file’s name, sample rate, mono or stereo, and length.
Trimming
The screen draws the IR’s waveform on a time axis in seconds. Start and End set the part of the file that is used, in milliseconds from the beginning of the file. Everything before Start and after End is dropped, and the dropped parts are dimmed on the screen. Turn the knobs, or touch the waveform and drag. A touch grabs whichever marker is nearer.
Once the file is analysed, the Start and End knobs span the length of that file. End cannot go past the end of the file, and Start always stays before End. Choosing a different IR file resets the trim to the whole file. Loading a preset keeps the preset’s trim.
Tone and Level
Low Cut and High Cut filter the convolved signal. They turn on a log scale, so each octave gets the same knob travel. At their extremes (20 Hz and 20 kHz) they are off, and the screen reads Off.
IRs are captured at very different levels, so Impulse IR evens them out as they load. Each IR is scaled so its loudest frequency between 80 Hz and 8 kHz sits at 0 dB: no IR boosts any part of the guitar range above the level it went in at, and switching IRs does not jump the volume. Trimming with Start or End re-levels the IR the same way. An IR with a darker or more scooped response can still sound a little quieter than a bright one.
Master sets the IR’s level after that, from -24 dB to +12 dB, with 0 dB at 12 o’clock. Use it when an IR still sounds louder or softer than the others. It changes only the convolved (wet) signal, so with Mix below 100 % it also shifts the balance against the dry signal.
Mix blends the convolved signal with the dry input. The INPUT and OUTPUT meters show the level going into and coming out of the device.
BYPASS turns the device off. Its light is on and the screen dims while the device is bypassed.
On the encoder dock, the first page holds Start, End, Low Cut, High Cut, and Mix, in panel order. The second page holds Master, and the standard device Gain and Output.
Tips
- Place a cabinet IR after an amp model and before time based effects unless a different order is part of the sound.
- Many cabinet IRs begin with a few milliseconds of silence. Move Start up to the first peak to remove the delay it adds.
- Shorten End to tighten a roomy cabinet capture, or to cut the tail of a room IR.
- Use Low Cut to remove boom and High Cut to tame fizz without changing the IR file.
- Level matching is automatic, so IR files can be compared by stepping through them with PREV IR and NEXT IR. Nudge Master for any that still stand out.